NYC1 Dock + Printer

Connect the USB-C cable to the power port on the dock and plug it into a power socket using the power adapter.

Next, connect your mobile device via cable using the data port on the dock or via Bluetooth. If you connect via cable, the dock will also charge your device.

1. Check if all the cables are connected, as described on the previous page.

2. Fasten the snap plate in the desired position using the included adhesive strip or screw.

3. Place the dock on top of the plate and push down gently until the dock snaps into place.

4. Place the card reader in the dock.

1. Press firmly on the bottom side of the paper hatch.

2. Place a new paper roll in the compartment.

3. Make sure the coated paper side is up and the paper aligns to the printing head.

4. Close the paper hatch and make sure it snaps into place.

This device is approved under Adyen N.V.

These instructions apply to the following product: NYC1 Dock + Printer

Read all safety information before using this device. This device is equipped with a rechargeable Li-ion Polymer battery.

• Recommended ambient operating temperature range: -10°C ~ +45°C (14°F ~ 113°F)

• Recommended ambient temperature range for safe battery charging is 0°C ~ +40°C (32°F ~ 104°F)

• The device is provided with a built-in battery. Don’t try to replace the battery. Contact your provider if you think the battery needs to be replaced.

• Do not dispose of the battery in fire.

• Do not disassemble, hit, crush, or burn the battery. If the battery is damaged, stop using the device immediately.

• Do not leave or store the device in areas that might get very hot.

• Do not open the device. Only qualifi ed personnel can open the device for repairs. Contact your provider if you think the device needs to be repaired.

• Keep the device out of reach of small children.

• Keep the device dry. Precipitation, humidity and liquid contain minerals that will corrode electronic circuits.

USA regulatory compliance

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

Caution: Any changes or modifications to this device not explicitly approved by manufacturer could void your authority to operate this equipment.

Canada regulatory compliance IC: 30044-XXXXXX

English: This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) This device may not cause interference, and (2) This device must accept any interference, including interference that may cause undesired operation of the device.

The digital apparatus complies with Canadian CAN ICES- 3 (B)/NMB-3(B).

This device meets the exemption from the routine evaluation limits in section 2.5 of RSS 102 and compliance with RSS 102 RF exposure, users can obtain Canadian information on RF exposure and compliance.

This equipment complies with Canada radiation exposure limits set forth for an uncontrolled environment.

French: Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exem pts de licence. L’exploitationestautorisée aux deux conditions suivantes: (1) l’appareil ne doit pas produir e de brouillage, et (2) l’utilisateur de l’appareildoit accepter tout brouillageradioélectriquesubi, mêmesi le brouillageest susceptible d’encompromettre le fonctionnement.

L’appareil numérique est conforme à CAN CAN ICES-3 (B) / NMB-3 (B).

Cet appareil est conforme à l’exemption des limites d’évaluation courante dans la section 2.5 du cnr - 102 et conformité avec rss 102 de l’exposition aux rf, les utilisateurs peuvent obtenir des données canadiennes sur l’exposition aux champs rf et la conformité.

Cet équipement est conforme aux limites d’exposition aux rayonnements du Canada établies pour un environnement non contrôlé.

RF Exposure Statement English: The device has been evaluated to meet general RF exposure requirement. The device can be used installed and operated with minimum distance 0mm between the radiator and your body.

French: L’appareil a été évalué pour répondre aux exigences générales d’exposition aux RF.Cet équipement doit être installé et utilisé avec une distance minimale de 0 mm entre le radiateur et votre corps.

EU regulatory compliance

Adyen N.V. hereby declares that this payment terminal is compliant with Directive 2014/53/EU and 2011/65/EU. The declaration of conformity can be accessed at:

https://www.adyen.com/licenses/nyc1-eu- declaration-of-conformity-dock-printer

EU representative: Adyen N.V. with address Simon Carmiggeltstraat 6-50, Amsterdam, Netherlands

UK regulatory compliance

Adyen N.V. hereby declares that this payment terminal is compliant with Radio Equipment Regulations 2017 and Restriction of the Use of Certain Hazardous Substances in Electrical and Electronic Equipment Regulations 2012. The declaration of conformity can be accessed at:

https://www.adyen.com/licenses/nyc1-uk- declaration-of-conformity-dock-printer

UK representative: Adyen UK Limited, with address 12-13 Wells Mews, London, England, W1T 3HE

Bluetooth® Wireless Technology

This is an approved Bluetooth® product. For more information about Bluetooth SIG listing, please visit:

https://www.bluetooth.com/

Disposal and recycling information

The symbol means that according to local laws and regulations your product shall be disposed of separately from household waste at the end of its working life. To prevent possible harm to the environment or human health from uncontrolled waste disposal, please separate this from other types of wastes and recycle it responsibly to promote the sustainable reuse of material resources.

EU operating frequencies and maximum transmit output power

Maximum radio-frequency power transmitted in the frequency bands in which the radio equipment operates. The maximum power for all bands is less than the highest limit value specifi ed in the related Harmonized standard. The frequency bands and transmitting power (radiated and/or conducted) nominal limits applicable to this radio equipment are as follows: